menu_icon

arrow_down
  • English
  • Français
  • Deutsch
  • Español
  • Italiano
  • Português

FEATURE SUMMARY

1. Lite Force Carbon™ Matrix Shell
Developed from premium 12K chopped carbon strands, expertly fused into our proprietary Carbon Mat. This intricate configuration ensures optimal energy dissipation on impact from any angle of impact, laying the foundation for unparalleled protection.
2. Optical Class 1 Face Shield Technology/ Pinlock® Ready Face Shield
APEX Series Optical Class 1 shield features varied thicknesses throughout the lens which enhances visual accuracy, reduces glare, and prevents distortion. Additionally, its specially designed shape was developed to improve aerodynamics and reduce wind noise during rides.
3. Optical Class 1 Adjustable SpeedView® SunVisor
The APEX Series Eclipse is equipped with our state-of-the-art, Optical Class 1 Sun Visor. Unlike typical sun visors that can distort vision because of their uniform thickness across a curved lens, the APEX Series Optical Class 1 shield features varied thicknesses throughout the lens which enhances visual accuracy, reduces glare, and prevents distortion.
4. Cool Tech™ Liner
Engineered to redefine comfort thanks to a unique adjustable crown pad design and an advanced material composition that offers exceptional comfort and moisture wicking properties.
6. Ellip-Tec® II Ratchet System
Easy, Secure, tool-less faceshield changes in seconds. Pulls the shield back against the eyeport gasket during closing to ensure a
7. AirFit® Liner Inflation System
Inflatable cheek pad bladders for a personalized fit.
8. Speaker Pockets
Speaker ducts designed into the EPS allow compatibility with communication unit speakers.
9. 3D Contoured Cheekpads
Plush removable and washable 3D contoured cheekpads for ultimate fit and comfort.
10. Emergency Release System
Tabs located under the neck roll allow easy removal of the cheek pads by emergency medical personnel thus allowing easier removal of the helmet.

SPEEDVIEW® INTERNAL SUN VISOR

NOTE: THE RETRACTABLE INTERNAL SUNVISOR CAN BE LOWERED AND RETRACTED, REGARDLESS OF WHETHER OR NOT THE FACESHIELD IS UP OR DOWN.
To lower the Sunvisor, slide the lever down.
To retract the Sunvisor back into rhe shell, slide the lever up.
warning icon WARNING
DO NOT attempt to adjust while riding.
For your comfort, the sun visor has 2 positions:
1) Top lever opens and closes the sun visor.
2) The lower lever adjuster provides 2 height options.
(Lever forward: sun visor bottom edge at maximum coverage. Lever back: sun visor bottom edge 5mm higher).:
*Be sure to set the lower adjustment lever to your preferred height before operating the top sun visor lever.

COOL TECH LINER REMOVAL

CHEEK PADS REMOVAL/INSTALLATION
Occasionally, cheek pads may need to be removed for washing or replacement.
REMOVAL - Gently pull the cheek pad away from the interior shell wall to release the 3 snaps. Then gently pull the lower cheek pad sleeve out from between the EPS and shell wall.
INSTALLATION - Align and slide the cheek pad sleeve hook (white arrow) in between the shell and EPS.This will ensure that the cheek pad snaps will align. Next insert the entire cheek pad sleeve in between the shell and EPS. Some force might be required. Once inserted, pull the chin strap through the cheek pad opening, then align and connect the 3 snaps.
CROWN LINER REMOVAL
Occassionally the crown liner may require removal for washing, replacement or to change sizes.
1. Remove the cheek pads.
2. At the back of the helmet pull the crown liner away from the shell unsnapping the two snaps.
3. Pull the crown liner out of the helmet while gently detaching it from the forehead channel.
AERO SKIRT REMOVAL/INSTALLATION
REMOVAL - Grasp and gently pull the Aero Skirt away from the chin bar (at angle shown), releasing the Aero Skirt tab from the chin bar channel. Next pull the remainder of the Aero Skirt sleeve free from between the shell and EPS.
INSTALLATION - Align and insert the Aero Skirt tab into the larger hole of the chin bar channel, then gently pry the bottom rubber gasket of the helmet back slightly to insert the remainder of the Aero Skirt between the shell and EPS.

AIRFIT® INFLATABLE LINER

INFLATION
While wearing the helmet press the large ball until you reach the desired fitment.
DEFLATION
Press the small button to release the air. DO NOT remove the helmet without first deflating the liner.
warning icon WARNING
DO NOT attempt to adjust while riding.
DO NOT modify, puncture, or damage the air bladders in any way. If the air bladders, or any other part of the inflation/deflation system becomes damaged or faulty, please contact your service provider.
The Aero Skirt does not require removal to access the AirFit inflate
Push-in the shield lock button and keep it pushed-in while lifting the shield upward.

EMERGENCY RELEASE SYSTEM

Locate the emergency labeling on the neck roll. Simply reach under the neck roll and grab the release strap, pull at a 45 degree angle towards front of helmet. The cheek liner will easily release from the helmet. This system should only be used by trained medical personnel.
warning icon WARNING
DO NOT attempt to adjust while riding.
In case of acciddent DO NOT attempt removal on you own.
NOTE: FIRST, OPEN OUTER SHIELD TO THE HIGHEST POSITION. THEN LOWER THE SUNVISOR TO LOWEST POSSIBLE POSITION.
FOR EASIER SUNVISOR REMOVAL: FIRST, REMOVE THE OUTER FACESHIELD.
To remove the sunvisor, firmly hold the sunvisor with your hand and gently pull one side out away from the helmet to release. Repeat to release the opposite side.
Reverse process for installation.

FACE SHIELD REMOVAL/INSTALLATION

IMPORTANT NOTE:
THE FACE SHIELD WHILE CAN ONLY BE REMOVED OR INSTALLED WHEN IN THE FULLY OPEN POSITION. NOT DOING SO WILL DAMAGE THE MECHANISM.
REMOVAL - 1) Fully open the shield. 2) Push the shield lever upward. 3) With the shield lever up, simultaneously pull the shield upward and away from the shell as shown. Repeat on the opposite side.
INSTALLATION - 1) Push and hold the lever upward. 2) Align the 3 tabs on the shield with the 3 corresponding channels on the baseplate. 3) Press the shield into the baseplate and slightly forward. The shield tabs will “click” into place. Open and close the shield a few times to ensure proper installation.
SHIELD LEVER

Warranty Info

WARRANTY
All ScorpionExo® helmets have a warranty of 5 years.
Although there is no visible damage on your helmet, general wear and tear over time may affect overall function of protective helmet and increase the risk of injury in accident. It is advisable to replace your helmet no later than every 5 years from purchase.
Should you have a warranty claim, go to your Scorpion dealer with your invoice (this is you purchase proof, it's necessary in order to start the warranty process).
You can find our dealers' list on ScoprionExo websites listed below (choose your country and then the location).
The dealer will contact our after sales service and start the warranty process in order to check and/or repair your helmet.
LIMITATION OF WARRANTY
NO WARRANTIES ARE OFFERED BEYOND THE LIMITED WARRANTY EXPRESSLY SET FORTH IN THIS MANUAL. TO THE FULLEST EXTENT PERMISSIBLEUNDER APPLICABLE LAW, WE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY, OMISSIONS, COMPLETENESS, CURRENTNESS AND DELAYS. IF THESE LIMITATIONS, CONDITIONS, AND OTHER POLICIES INCORPORATED BY REFERENCE ARE HELD TO BE UNENFORCEABLE, OUR LIABILITY FOR DAMAGES SHALL NOT EXCEED THE AMOUNT PAID BY PURCHSER(S) OF SUCH PRODUCT(S)

Other Information

COPYRIGHTS
Copyright © 2020 Kido Sports Co., Ltd. All rights reserved. No part of this guide may be reproduced in any form or by any process whatsoever without prior written consent from the copyright holder.
LICENSES
The ScorpionExo® and the EXO-Com® trademark/logo are exclusively owned by Kido Sports Co., Ltd. Any use of the mark by any other parties without prior written permission of Kido Sports Co., Ltd. constitutes an infringement of legal rights. The Bluetooth® trademark is owned by Bluetooth SIG, and is used under license by BITwave Pte Ltd.
IC/SAR COMPLIANCE STATEMENT

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209.

This equipment should be installed and operated with minimum distance 0 mm between the radiator and your head. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209.

Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

FCC/SAR COMPLIANCE STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the Equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.919 W/kg.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

CE/SAR COMPLIANCE STATEMENT

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.

End user must follow the specific operating instructions for satisfying RF exposure compliance. These requirements set a SAR limit of 2.0 W/kg averaged over one gram of tissue. To meet the above requirement, the device should be placed at least 5mm away from human body in normal use condition.