menu_icon

arrow_down
  • English
  • Français
  • Español
  • 中文

FEATURE SUMMARY

NOTE: LINE ARTS SHOWN IN THIS MANUAL ARE FOR REFERENCE ONLY AND MAY VARY FROM ACTUAL PRODUCT.
1. Pinlock® Prepared Faceshield
The shield is with Anti-Scratch hardened coating, and is ready for Pinlock Max Vision system, thr world’s best fog free resistant system.
2. KwikWick® C Liner Fabric
KwikWick® C anti-microbial fabric keeps you cool and dry in warm weather, warm in cool weather Liner is easily removable and washable.
3. KwikFit™
KwikFit™ cheekpads allow easy on and off of PRESS UP TO RELEASE the most common styles of eye glasses
4. Ellip-Tec™ II Ratchet System
Easy, Secure, tool-less faceshield changes in seconds. Pulls the shield back against the eyeport gasket during closing to ensure a proper seal.
5. Aero-Tuned Ventilation
Five intake ports across the front of helmet forces cool air in while four exhaust vents maximize movement of hot air out.
6. Face Shield Lock / Vent System
Shield securely locks in place. Or use City Mode for a light air flow when riding at low speeds.
7. Advanced Dual-Density EPS:
Advanced multi-layer EPS provides efficient energy displacement in key areas. EPS liner throughout entire chin bar area.

FACESHIELD LOCK & VENT LEVER

To lock the faceshield, turn Locking-lever counter- clockwise to the 2 o’clock position approximately.
Check faceshield if it’s securely locked.
To unlock the faceshield, and provide air flow at low speeds, turn Locking-lever clockwise to the 5 o’clock position.
Test faceshield to check if it is unlocked.
Note: First, close shield to the lowest position to lock/unlock.
When the lever is positioned at 3 o’clock, the shield is closed, but it is also unlocked.
NOTE: THE FACESHIELD CAN ONLY BE REMOVED OR INSTALLED WHEN IN THE FULLY OPENED POSITION!!!
To remove the faceshield, place the helmet in front of you with the eye port facing away. Ratchet the faceshield up to the fully open position. Using both hands, push up the Y shape release latchet upward and the shield is able to release out of locking mechanism. Then, with both of your thumbs pushing squarely on the center of the Ellip-Tec® II, gently pull or “peel” the faceshield away from the helmet.
To install the faceshield, make sure the faceshield axis (1) and the stopper (2) are positioned properly as shown in the below picture. Then push the axis (1) first, and then push the stopper (2) strongly so that they can be sat on the right track. Test the faceshield by opening and closing it several times to verify it is properly installed.
IMPORTANT NOTE: Be sure to latch up the “Y” release latchet while removing the faceshield!
DO NOT attempt to adjust while riding.

KWIKWICK® C

CHEEK PADS REMOVAL
1. Grip one cheek pad by slipping your fingers behind the pad near the eyeport. Gently pull the cheek pad away from the helmet to release the three plastic retainer snaps.
2. Remove the plastic cheek pad flange from the helmets lower rim along the rubber trim. Reverse entire process to reinstall.
CROWN LINER REMOVAL
Occassionally the crown liner may require removal for washing, replacement or to change sizes.
First, remove the Cheek Pads.
At the back of the helmet pull the crown liner away from the shell.
Pull the crown liner out of the helmet while gently detaching it from the forehead channel.
Reverse this process for installation.
AERO SKIRT REMOVAL
The pliable Aero Skirt was designed to reduce wind from entering behind the face shield area, specifically to keep your face warmer in cold weather.
You do however have the option to remove the Aero Skirt for cleaning or for warmer riding conditions.
TO REMOVE Simply tug on the Aero Skirt and it slides out of the rubber trim channel.
Reverse this process to re-install.

Warranty Info

WARRANTY
All ScorpionExo® helmets have a warranty of 5 years.
Although there is no visible damage on your helmet, general wear and tear over time may affect overall function of protective helmet and increase the risk of injury in accident. It is advisable to replace your helmet no later than every 5 years from purchase.
Should you have a warranty claim, go to your Scorpion dealer with your invoice (this is you purchase proof, it's necessary in order to start the warranty process).
You can find our dealers' list on ScoprionExo websites listed below (choose your country and then the location).
The dealer will contact our after sales service and start the warranty process in order to check and/or repair your helmet.
LIMITATION OF WARRANTY
NO WARRANTIES ARE OFFERED BEYOND THE LIMITED WARRANTY EXPRESSLY SET FORTH IN THIS MANUAL. TO THE FULLEST EXTENT PERMISSIBLEUNDER APPLICABLE LAW, WE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY, OMISSIONS, COMPLETENESS, CURRENTNESS AND DELAYS. IF THESE LIMITATIONS, CONDITIONS, AND OTHER POLICIES INCORPORATED BY REFERENCE ARE HELD TO BE UNENFORCEABLE, OUR LIABILITY FOR DAMAGES SHALL NOT EXCEED THE AMOUNT PAID BY PURCHSER(S) OF SUCH PRODUCT(S)

Other Information

COPYRIGHTS
Copyright © 2020 Kido Sports Co., Ltd. All rights reserved. No part of this guide may be reproduced in any form or by any process whatsoever without prior written consent from the copyright holder.
LICENSES
The ScorpionExo® and the EXO-Com® trademark/logo are exclusively owned by Kido Sports Co., Ltd. Any use of the mark by any other parties without prior written permission of Kido Sports Co., Ltd. constitutes an infringement of legal rights. The Bluetooth® trademark is owned by Bluetooth SIG, and is used under license by BITwave Pte Ltd.
IC/SAR COMPLIANCE STATEMENT

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209.

This equipment should be installed and operated with minimum distance 0 mm between the radiator and your head. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209.

Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

FCC/SAR COMPLIANCE STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the Equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.919 W/kg.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

CE/SAR COMPLIANCE STATEMENT

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.

End user must follow the specific operating instructions for satisfying RF exposure compliance. These requirements set a SAR limit of 2.0 W/kg averaged over one gram of tissue. To meet the above requirement, the device should be placed at least 5mm away from human body in normal use condition.