ADF-9000 SERIES/EXO-XT9000 CARBON Feature Manual

FEATURE SUMMARY

LINE ARTS SHOWN IN THIS MANUAL ARE FOR REFERENCE ONLY AND MAY VARY FROM ACTUAL PRODUCT.

CITY MODE: Unlock the faceshield by pressing your thumb up on the faceshield lever until it snaps open. Leave open at first detent to provide air flow at low speeds.



2. SPEEDVIEW^® SUNVISOR: Retractable interchangeable internal sun visor. Features exclusive Everclear^® anti-fog coating on all surfaces.
3. EMERGENCY RELEASE SYSTEM: 3D contoured, Kwikfit^® cheek pads featuring EMT-friendly, emergency release design.
4. AIRFIT^® LINER INFLATION SYSTEM: Integrated cheek pad air bladder adjustment system provides a personalized fit.
5. KWIKWICK^® III LINER FABRIC: Removable and washable liner featuring a supple hypo-allergenic, anti-microbial treated interior with advanced moisture-wicking properties.
6. AERO-TUNED VENTILATION: Features 2 adjustable ram air intakes that force fresh air towards multiple internal channels pulling heat and humidity up and out the rear exhaust ports integrated into the rear spoiler.
7. ACTION CAM MOUNTING PLATE: Flat surface to mount cameras and other accessories (includes vent plate & screw only)
8. SPEAKER POCKETS: Speaker cavaities built into the EPS allow for speakers up to 50mm.

PEAK VISOR REMOVAL

ACTION CAM MOUNTING PLATE INSTALL

TO INSTALL:

1. First fully open the mouth vent door by pressing at the bottom of the vent door.

With the vent fully open, firmly pry/pull the vent door away from the vent housing.

With the door removed, simply align the included mounting plate screw hole with the screw hole in the vent housing, then insert and tighten the included screw.

2. Reverse to remove the cam plate and reinstall the vent door.

FACESHIELD REMOVAL

To avoid scratching the shield during removal, first turn the peak-visor center screw counter-clockwise by 1/4 turn [Fig 1. on Pg 2] and then lift peak-visor upward

1. The peak/visor will rotate backward and out of the way.

2. Open the shield until the triangle shapes are facing each other.

3. Once aligned, firmly grasp and pull the shield forward at an angle that matches the shield notch

4. Return the peak/visor to the riding position, press the top screw into place and turn the screw clockwise to full re-attach.

REMOVING THE SUN VISOR

NOTE

The Retractable internal SunVisor can be lowered and retracted, with the faceshield in the open or closed position.

To lower the SpeedView^® SunVisor slide the lever down

To retract the SpeedView^® SunVisor back into the shell, slide the lever up.

NOTE: FIRST, OPEN OUTER SHIELD TO THE HIGHEST POSITION. THEN LOWER THE SUNVISOR TO LOWEST POSSIBLE POSITION. To remove the sunvisor, firmly hold the sunvisor with your hand and gently pull one side out away from the helmet to release. Repeat to release the opposite side. Reverse process for installation.

PEAK VISOR ANGLE

AIRFIT^® LINER INFLATION SYSTEM

INFLATION: While wearing the helmet, press the pump located at the front of the chin bar until you reach your desired fitment.

DEFLATION: Press the small pressure release button located beside the pump. DO NOT attempt to remove your helmet before deflating the air bladders.

DO NOT attempt to adjust while riding.

DO NOT modify, puncture, or damage the air bladders in anyway. If any part of the AirFit^® system is damaged or faulty in any way. please contact ScorpionEXO^®

Locate the emergency labeling on the neck roll. Simply reach under the neck roll and grab the release strap, pull at a 45 ̊ degree angle towards the front of the helmet. The cheek pads will easily release from the helmet. This system should only be used by a trained medical personal.

DO NOT attempt to adjust while riding. In case of accident DO NOT attempt removal on your own.

KWIKWICK^® III LINER REMOVAL

CHEEK PADS REMOVAL

Occassionally the cheek pads may require removal for washing or replacement.

1. Remove the Aero Skirt.

2. Slide your thumb behind the cheek pad at the area closest to the AirFit inflation pump.

3. Gently tug the cheek pad away from the helmet interior wall. There are three plastic snaps that require unsnapping. At the same time slide the plastic trim out of the helmet channel.

Repeat this process for both cheek pads.

Reverse this process for installation.

CROWN LINER REMOVAL

Occassionally the crown liner may require removal for washing, replacement or to change sizes.

1. Remove the cheek pads.

2. At the back of the helmet pull the crown liner away from the shell unsnapping the two snaps.

3. Pull the crown liner out of the helmet while gently detaching it from the forehead channel.

Reverse this process for installation.

AERO SKIRT REMOVAL

The pliable Aero Skirt was designed to reduce wind from entering behind the face shield area, specifically to keep your face warmer in cold weather.

You do however have the option to remove the Aero Skirt for cleaning or for warmer riding conditions.

TO REMOVE Simply tug on the Aero Skirt and it slides out of the rubber trim channel.

Reverse this process to re-install.

WARNING

Small neodymium magnets are used for easier operation. The magnet force is not very strong, and generally each magnet size is not considered as dangerous.

However, consult your physician before using if you are a pacemaker wearer and not sure about the 7 effect caused by these magnets.

Warranty Info

WARRANTY: All ScorpionExo^® helmets have a warranty of 5 years.
Although there is no visible damage on your helmet, general wear and tear over time may affect overall function of protective helmet and increase the risk of injury in accident. It is advisable to replace your helmet no later than every 5 years from purchase.
Should you have a warranty claim, go to your Scorpion dealer with your invoice (this is you purchase proof, it's necessary in order to start the warranty process).
You can find our dealers' list on ScoprionExo websites listed below (choose your country and then the location).
The dealer will contact our after sales service and start the warranty process in order to check and/or repair your helmet.
LIMITATION OF WARRANTY: NO WARRANTIES ARE OFFERED BEYOND THE LIMITED WARRANTY EXPRESSLY SET FORTH IN THIS MANUAL. TO THE FULLEST EXTENT PERMISSIBLEUNDER APPLICABLE LAW, WE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY, OMISSIONS, COMPLETENESS, CURRENTNESS AND DELAYS. IF THESE LIMITATIONS, CONDITIONS, AND OTHER POLICIES INCORPORATED BY REFERENCE ARE HELD TO BE UNENFORCEABLE, OUR LIABILITY FOR DAMAGES SHALL NOT EXCEED THE AMOUNT PAID BY PURCHSER(S) OF SUCH PRODUCT(S)

Other Information

COPYRIGHTS

LICENSES

The ScorpionExo^® and the EXO-Com^® trademark/logo are exclusively owned by Kido Sports Co., Ltd. Any use of the mark by any other parties without prior written permission of Kido Sports Co., Ltd. constitutes an infringement of legal rights. The Bluetooth^® trademark is owned by Bluetooth SIG, and is used under license by BITwave Pte Ltd.

IC/SAR COMPLIANCE STATEMENT

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209.

This equipment should be installed and operated with minimum distance 0 mm between the radiator and your head. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209.

Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

FCC/SAR COMPLIANCE STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the Equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.919 W/kg.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

CE/SAR COMPLIANCE STATEMENT

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.

End user must follow the specific operating instructions for satisfying RF exposure compliance. These requirements set a SAR limit of 2.0 W/kg averaged over one gram of tissue. To meet the above requirement, the device should be placed at least 5mm away from human body in normal use condition.